Cornelius Wrecking
← Back to Blog

Silica Compliance in Demolition: What OSHA Requires

Silica Compliance in Demolition: What OSHA Requires

Red excavator breaking concrete during demolition

If your crew breaks up concrete, brick, block or masonry, you are creating respirable crystalline silica, and OSHA’s construction silica standard, 29 CFR 1926.1153, almost certainly applies to the job. Compliance comes down to four things: knowing which tasks expose people, choosing between the standard’s two compliance routes, controlling dust at the source, and putting the plan and the paperwork in writing before the first wall comes down. This guide walks owners, general contractors and safety managers through each one.

Corneliuswrecking
Plan Demolition With Safety in Mind
Cornelius Wrecking provides demolition services and holds OSHA and asbestos abatement certifications for projects involving complex safety requirements.
Explore demolition services

TL;DR

  • Demolition that crushes, abrades or fractures concrete, brick or block releases respirable crystalline silica. OSHA’s standard covers it unless exposure will stay below 25 micrograms per cubic meter under any foreseeable conditions.
  • You have two routes: follow Table 1 fully and properly, or use the alternative method with exposure assessment and controls that hold workers at or below the 50 micrograms per cubic meter limit.
  • Water or dust suppressants, sealed and filtered equipment cabs, and housekeeping that does not stir up settled dust are the core controls on heavy-equipment demolition.
  • A written exposure control plan, a designated competent person, training, and exposure and medical records are part of compliance, not extras.
  • Ask any demolition bidder to show how silica is handled in its plan before you award the work.

Table of Contents

Why demolition is a silica problem

Crystalline silica is a common mineral. According to CDC’s NIOSH silica guidance, it is typically found in soil, sand, concrete, mortar, granite and other minerals. Intact, those materials are not the hazard. The hazard starts when someone breaks them. Respirable particles are small enough to be inhaled deep into the lungs, and NIOSH notes that silica dust can become airborne whenever work disturbs silica-containing materials.

Demolition is about as direct a route to that dust as construction offers. OSHA’s guidance on heavy equipment states that using heavy equipment or utility vehicles to demolish, abrade or fracture silica-containing brick, block or concrete can generate respirable crystalline silica. An excavator with a hydraulic hammer on a concrete slab, a processor crushing a column, a skid steer sweeping debris: each one puts fine dust in the air, and much of it is invisible at the particle size that matters.

The health stakes

NIOSH reports that inhaling respirable crystalline silica causes silicosis, which is irreversible but preventable, and that exposure at work also causes lung cancer. OSHA adds that silica-related diseases occur after years of exposure in most cases. That delay is why silica is easy to neglect: nobody on site feels sick on the day the dust is created. A crew that works without controls for a decade can carry the consequences for the rest of its working life, and the people who owe those workers a safe site are the employers who set the controls.

Which OSHA rule applies to your demolition work

U.S. demolition contractors doing construction work generally fall under OSHA’s Respirable Crystalline Silica standard, 29 CFR 1926.1153. The one exception written into the rule is narrow: the standard does not apply if the employer can show that employee exposure will remain below 25 micrograms per cubic meter, measured as an 8-hour time-weighted average, under any foreseeable conditions.

On a demolition site, that exception is hard to rely on. Conditions change by the hour: wind, enclosure, the material being broken, how many machines are working at once. Most contractors treat the standard as applicable and build their safety program around it, which is also what most owners expect to see in a bid.

The standard is a federal rule. Some states run their own OSHA-approved plans with their own requirements, so confirm which agency has jurisdiction where your project sits. Our work spans Missouri, Kansas, Iowa and Nebraska, and for any project we confirm jurisdiction and local permit rules during planning. For a Missouri job, our guide to demolition permits and notice periods in Missouri covers the paperwork that runs alongside the safety plan.

Which OSHA rule applies to your demolition work — overview diagram

Two ways to comply: Table 1 or the alternative method

OSHA gives employers two compliance routes. According to OSHA’s standard summary, you can fully and properly follow the task-specific engineering controls, work practices and respirator provisions in Table 1, or you can use the alternative method, which requires exposure assessment and controls sufficient to meet the permissible exposure limit of 50 micrograms per cubic meter.

Table 1 route Alternative route
How it works Match each listed task to its specified controls and respirator requirements, and implement them fully and properly Assess exposure, then use controls that keep it at or below the 50 micrograms per cubic meter limit
Exposure measurement Not required for tasks covered by fully and properly implemented Table 1 controls Required, by air monitoring or objective data
Best fit Common, repeatable tasks that Table 1 lists Tasks Table 1 does not cover, or conditions that differ from what Table 1 assumes
Main risk Partial implementation: a missing control means the task is no longer covered Weak data: assessments that do not reflect real site conditions

The phrase that matters in the first route is “fully and properly.” If a Table 1 task calls for water delivery and a respirator, and the water is not reaching the cut, the task falls outside the safe harbor. At that point the employer must treat it under the alternative route, with exposure assessment, and the burden of proof shifts.

Exposure limits and how to assess them

The numbers are fixed. Under 29 CFR 1926.1153, the action level is 25 micrograms per cubic meter and the permissible exposure limit is 50 micrograms per cubic meter, each calculated as an 8-hour time-weighted average. The action level triggers some obligations; the PEL is the ceiling your controls must hold.

For tasks not covered by fully and properly implemented Table 1 controls, the employer must assess exposure in one of two ways:

  1. Performance-style data. Use sufficient air-monitoring data or objective data to characterize exposure.
  2. Scheduled personal sampling. Sample in the worker’s breathing zone, scheduled by shift, job classification and work area.

Assessment is not one-and-done. The rule requires reassessment when changes may reasonably be expected to produce new or additional exposures at or above the action level, or when there is reason to believe such exposures have occurred. On a demolition project, that happens often: a new phase, a different structure, a change from exterior to interior work, a second subcontractor moving in. Build reassessment into the schedule rather than waiting for a complaint.

Controlling dust on heavy-equipment demolition

Most demolition silica exposure is a machinery story, and OSHA has published specific guidance for it. Three controls do most of the work.

Water and dust suppressants

OSHA’s guidance says to apply water or dust suppressants so materials are damp when disturbed, at a rate sufficient to minimize visible dust. The same guidance requires this when other workers are present around heavy-equipment demolition. In practice that means:

  • hose or spray-bar coverage aimed at the point of impact, not at the pile after the fact;
  • enough water pressure and supply to keep up with the machine, which is a logistics question as much as an equipment one;
  • a plan for runoff and slurry, since wet work creates its own cleanup and site-drainage issues.

Sealed, filtered operator cabs

OSHA states that demolition operators can reduce exposure by working in a well-sealed, positively pressurized enclosed cab with doors and windows closed, heating and air conditioning, and intake filtration at least 95% efficient in the 0.3 to 10.0 micrometer range, for example MERV-16 or better. The detail that trips people up is the word “closed.” A pressurized cab with the door propped open protects nobody. Operators also need a habit of keeping the cab clean: OSHA says to regularly clean and maintain enclosed cabs so settled dust does not become airborne again.

Diagram of sealed cab silica dust controls

Cab filtration is one layer of a wider approach to fine dust. When the demolition work is done and the site moves toward turnover, post-construction cleaning equipment with HEPA filtration is the type of tool that keeps captured dust from going back into the air during final cleanup.

Housekeeping that does not make it worse

Settled silica dust is a second source. Dry sweeping and compressed air put it back into the breathing zone. Your plan should say what method is used to clean, who does it, and where the debris goes. For disposal rules that vary by state, see our summary of landfill disposal rules for demolition waste in Nebraska as an example of what to check before hauling begins.

The written exposure control plan

The standard requires a written exposure control plan, and OSHA’s construction silica information page spells out what it must contain:

  • a description of the tasks that expose employees to silica;
  • the engineering controls, work practices and respiratory protection used for each task;
  • the housekeeping measures used to limit exposure;
  • procedures restricting access to work areas, so exposure is limited, including exposure generated by other employers or sole proprietors.

The plan must be reviewed at least annually and updated as needed. A designated competent person must make frequent and regular inspections to implement it.

The access-restriction item deserves attention on multi-trade sites. If your crew is cutting concrete while another contractor’s workers stand downwind, your plan has to account for them. This is where owners and general contractors should ask direct questions: who is the competent person, where is the plan kept, and how are other trades kept out of the dust zone? Our article on putting OSHA surveys and safety obligations in demolition contracts shows how to move those answers into contract language, and the industrial demolition safety plan guide for owners covers how silica fits among the other hazards on a plant or factory teardown.

Respirators, medical exams, training and records

Respirators are required when Table 1 specifies them, or when feasible engineering and work-practice controls cannot reduce exposure to the PEL, according to OSHA’s standard overview. Respirators are the last line of defense, not the first. A program that leans on masks because the water system never worked is the kind that fails an inspection.

The same OSHA document lists the supporting duties:

  • Medical surveillance. Medical exams every three years for workers who are required to wear a respirator for 30 or more days per year.
  • Training. Covered workers must be trained on the hazard and on the controls that protect them.
  • Records. Employers must keep exposure records and medical-exam records.

If a respirator program applies, it comes with its own requirements for fit and use under OSHA’s wider respiratory protection rules, so confirm those with your safety professional or occupational physician before sending a crew out.

Our perspective: silica compliance is a scheduling and accountability problem

When people talk about silica, they talk about equipment and numbers. What we see on real jobs is that the failures are usually handoffs. The demolition contractor assumes the abatement contractor handled the dust. The abatement contractor leaves, and nobody owns the water supply. A subcontractor operates a machine with a cab nobody has checked since the last job.

That is why we keep demolition, excavation and hazardous material removal under one roof, with our own crew and equipment. We hold OSHA and asbestos abatement certifications, and managing hazardous material removal internally means fewer gaps between phases and one party answerable for the whole site. For industrial, energy and public-sector work, where several hazards overlap, that single line of accountability matters more than any single piece of equipment.

Our advice to owners: do not accept “we follow OSHA” as an answer. Ask the contractor which tasks on your building create silica, which Table 1 entries or alternative-method data cover them, who the competent person is, and where the written plan lives. A bidder who can answer those in a few minutes has done the work. One who cannot is asking you to carry the risk.

— Zach

Where Cornelius Wrecking fits

We handle commercial, industrial and municipal demolition, asbestos abatement, concrete and asphalt tear out, and excavation across Missouri, Kansas, Iowa and Nebraska, with large-scale work nationwide. If you are planning a teardown and want silica controls, abatement and demolition coordinated by one contractor, start with our industrial demolition services or asbestos abatement services.

Corneliuswrecking

Public agencies can see how we approach government work on our municipal and government demolition page. When you write a bid package, our guide to demolition RFP requirements lists what owners specify and what bidders should be ready to prove.

FAQ

Does the OSHA silica standard apply to every demolition job?

Generally yes, for construction work. The standard does not apply only if the employer can show exposure will stay below 25 micrograms per cubic meter as an 8-hour average under any foreseeable conditions, per 29 CFR 1926.1153. On demolition sites, with changing conditions and heavy equipment, that is difficult to demonstrate, so most contractors plan to comply.

What is the silica exposure limit in demolition?

The permissible exposure limit is 50 micrograms per cubic meter of air, averaged over an 8-hour shift, and the action level is 25 micrograms per cubic meter. Both come from the same federal construction standard. If you follow Table 1 fully and properly, you do not have to measure exposure for those tasks.

Can water alone keep a demolition site compliant?

Not by itself in every case. OSHA’s heavy-equipment guidance calls for water or dust suppressants at a rate that minimizes visible dust, and it also describes enclosed, filtered cabs for operators. Whether water is enough for a given task depends on what Table 1 requires for it, or on exposure data under the alternative method.

What belongs in a silica exposure control plan?

The plan describes the tasks that expose workers, the controls and respiratory protection for each task, housekeeping measures, and procedures to restrict access, including exposure created by other employers. It must be reviewed at least annually, and a competent person must inspect the site regularly to implement it.

Do workers need medical exams?

OSHA requires exams every three years for workers who must use a respirator for 30 or more days per year. Training and exposure records are also required for covered workers, as described in OSHA’s standard summary.

Sources

Planning a demolition or excavating project?

Get a fast, no-obligation quote from Cornelius Wrecking.

Request a Quote